Save time when finishing porous woods by using Glowmax Sealcoat Universal Sanding Sealer. This high-build solution seals the wood, creating a surface that’s easy to sand and contributes to an ultra-smooth final finish. Glowmax Sealcoat penetrates deeply into the wood grain, forming a thin yet strong base coat that ensures a durable bond between the wood and the top coat, enhancing the overall finish quality.
• Compatible with ALL clear wood finishes
• Great for sealing ALL interior wood, including floors
• Dries lightning fast – can be sanded & recoated in minutes
• Does not darken or yellow with age
• Easy clean up with alcohol or ammonia and water
• Gives extra beauty & warmth to water-base polyurethanes
• Can be used as a pre-stain conditioner for pine and softwoods
• Can be used as a bond coat under new finishes – adheres to any existing finish.
FOR BEST RESULTS
Be sure surface is smooth, clean, dry and sound. Remove any wax with mineral spirits. Apply two coats to improve film build and give added depth to the final finish.
AVAILABLE SIZES
• 1 ltr
• 5 ltrs
• 20 ltrs
Stir well before and occasionally during use. Apply several thin coats of ‘GLOWMAX Sealcoat’ with sprayer, brush, pad or lint-free muslin cloth. Multiple thin coats are more effective than 1 or 2 thick coats. Apply evenly and allow drying for 20 to 30 minutes before sanding with 120 or finer grit sandpaper. The subsequent coats should be let dry for 20 to 30 minutes before sanding and recoating. It completely dries in less than 1 hour and can be sanded & coated with ‘GLOWMAX Topcoat’ subsequently.
Methods:
Wiping
Dilute ‘GLOWMAX Shellac Finish & Sealer’ with Thinner/ Moisture-less Spirit in the ratio of upto 1:3 when applying with a muslin cloth pad. Apply the mixture with gentle pressure over the wood surface, in the direction of the grains, till desired result is achieved.
Brushing
For best results use a 2” or 3” natural bristle or high quality synthetic bristle brush. Dip half the length of the bristles into the container containing GLOWMAX and lightly tap the flat side of the brush against the side of the container. Apply to the surface following the wood grains and using full, even strokes. When applying to vertical surfaces, avoid drips and runs by loading the brush with a little less solution. Avoid Excessive brushing. Dilute with NC/Retarder Thinner in the ratio 1:2 or more if required.
Sprayer
GLOWMAX can be spray applied using conventional, HVLP or air-less systems. Use a 0.011 to 0.013 tip and 800 to 1000 psi for spray application (Follow Equipment manufacturers instructions). While spraying GLOWMAX, do it in the direction of the wind.
- Appearance:Clear liquid
- Odor: Alcohol type odor
- Physical State: Liquid
- PH: 5.2 – 5.5
- Boiling Point: 77.7778° – 85° C
- Melting/Freezing Point: -113.889° C Auto-ignition Temp: 362.778° F
- Viscosity: 15 cps
- Specific Gravity (water = 1): 0.87
- Water Solubility: The alcohol portion is soluble in water, the shellac portion is not soluble and will from a gelatinous layer on top of water.
Handling:
Keep away from heat, spark, and flame. Keep operating temperatures below ignition temperatures at all times. Use with adequate ventilation. Avoid contact with eyes, skin and clothing.
Storage:
Store in a Cool Dry place away from heat. Keep away from heat, sparks and flame. Keep containers tightly closed and upright when not in use. Protect against physical damage. Physical Data Appearance: Clear liquid Odor: Alcohol type odor Physical State: Liquid PH: 5.2 – 5.5 Boiling Point: 77.7778° – 85° C Melting/Freezing Point: -113.889° C Auto-ignition Temp: 362.778° F Viscosity: 15 cps Specific Gravity (water = 1): 0.87 Water Solubility: The alcohol portion is soluble in water, the shellac portion is not soluble and will from a gelatinous layer on top of water.